INDUFLEX-MS_GB_TM_1017.pdf
2 Halaman
53,1 KB
Download
<h1>INDUFLEX-MS_GB_TM_1017.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2 – 8 <br />D-32760 Detmold (Germany) <br />phone + 49 -5231- 953-00 <br />fax <br />+ 49 -5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>INDUFLEX-MS INDUFLEX-VK6065 </p> <p>Art.-No. 2 06402 <br />MS Hybrid-Polymer joint sealant for processing plants for effluent slurry, <br />manure slurry, silage effluent <br />• MS Hybrid-Polymer – joint sealant <br />• Thixotropic <br />• Elastic <br />• Stable against water under pressure up to a <br />maximum of 1.0 bar (when stably back-filled) <br />• Assured bond to concrete, cement-based screeds, <br />steel, masonry work etc. <br />• Impenetrable to liquids even under deformation <br />• High chemical resistance against organic acids <br />• Free from solvents <br />• Assured bond to non-absorbent substrates <br />• High UV resistance <br />Areas of application: <br />INDUFLEX-MS is used in interior and exterior <br />areas as an elastic joint sealant in construction: <br />• Waste water inspection shafts <br />• Sewer pipes <br />• Pre-cast concrete sections, e.g. drive-in silos <br />• Concrete overflow gullies <br />• Concrete storage containers <br />• Processing plants for effluent slurry, manure slurry, <br />silage effluent <br />Technical Data: <br />Basis: <br />MS hybrid polymer <br />Colour: <br />black (RAL 7021) <br />Consistency: thixotropic <br />Density: <br />approx. 1.35 g/cm3 <br />Solids content: <br />100% <br />Solvent: none <br />Max. reliable deformation <br />(ISO 11600): <br />20% <br />*) <br />Skin formation time : <br />approx. 15 mins. <br />*) <br />Through hardening rate : approx. 3 mm/24 hrs <br />Tack free time <br />*) <br />after approx. 4 hrs <br />(EN ISO 868) : <br />Shore A hardness: <br />approx. 55</p> <p>Volume change <br />(EN ISO 105653): <br />< 4% <br />Tensile stress value: <br />approx. 1.20 N/mm2 <br /> (DIN 53504) <br />Breaking strength: <br />approx. 1.50 N/mm2 <br /> (DIN 53504) <br />Temperature resistance: from -40° C to +100° C <br />Volume change: <br />0 <br />Cleaning: thoroughly clean tools <br />immediately after use with <br />an appropriate cleaner, e.g. <br />ASO-R001 <br />Packaging: <br />600 ml sausage <br />Storage: cool and dry; cartridge: <br />9 months in the original <br />unopened container, min. <br />+5°C to max. +25°C. Use <br />opened containers promptly. <br />*) These values are valid at +23°C and 50% relative humidity.</p> <p>Substrate: <br />Cement-based surfaces: <br />• Concrete quality: min. C 20/25 <br />• Screed quality: min. EN 13813 CT-C25-F4 <br />• Age: min. 7 days (or min. 70% of the 28 day <br />final strength) <br />• Tensile adhesion strength: > 1.5 N/mm2 <br />Steel: <br />• Steel rails/profiles <br />• Steel gutters <br />• Steel pipes <br />Substrate preparation: <br />The contact area to which the product will be applied <br />must: <br />• be dry, sound, load-bearing and have a good grip <br />• be free from separating and adhesion inhibiting <br />substances such as dust, laitance, grease, oil, <br />plasticizers, rubber marks, rust, paint residues etc.</p> <p>1/2</p> <p>10/17</p> <p>Dependent on the particular substrate the following <br />preparation measures are to be carried out: <br />Cement-based surfaces: <br />• Abrasion <br />Steel surfaces: <br />• Bright metal (Sa 21/2) <br />Design requirements: <br />The design requirements for joint construction must be <br />as given in accordance with DIN 18540 as well as the <br />IVD data sheet No.1 (Industrial Sealants Association) <br />and verified on site. <br />In particular the joint width must be calculated so that <br />the total joint movement is not greater than that suitable <br />for the joint sealant. <br />Product preparation: <br />INDUFLEX-MS is delivered ready-for-use in 600 ml <br />sausages and is to be used with a suitable gun. Strike <br />off the sealant with a suitable smoothing tool and press <br />onto the joint edges and backfilling profile or stable <br />backfilling material. Within the product working time <br />smooth the joint surface if required by lightly smoothing <br />over with a spatula or soft brush with the aid of a <br />smoothing solution. <br />Method of application / consumption: <br />1. Prepare the joint void by blocking with a suitable <br />closed cell backing strip. In the process, ensure that <br />the backing strip does not become damaged. <br />2. Prime the joint edges. Pre-treat highly absorbent <br />mineral-based joint edges with INDU-Primer-S, nonabsorbent joint edges with INDU-Primer-N. <br />3. Before applying sealants, protect joint flanks from <br />contamination with a self adhesive strip. <br />4. Apply the joint sealant: INDUFLEX-MS is installed with <br />a suitable caulking gun.</p> <p>The consumption of INDUFLEX-MS is calculated using <br />the formula: <br />joint width (mm) x filling depth of the sealant (mm) = <br />ml/m joint. <br />Example: <br />Joint dimension: <br />Joint width 20 mm and fill depth 17 mm = 1.75 m per <br />600 ml sausage. <br />During the curing time exclude early stresses (e.g. very <br />high temperature differences; vehicular traffic with direct <br />contact). <br />Important advice: <br />• Higher temperatures reduce the working time. Lower <br />temperatures lengthen the working time and setting <br />time. <br />• The bond between the individual materials can be <br />heavily impeded through the influence of dampness <br />or contamination between the two layers. <br />• Applications that are not clearly mentioned in <br />this technical data sheet may only be carried out <br />after consultation and written confirmation from the <br />Technical Services Department of SCHOMBURG. <br />Please observe a current EU health and safety data <br />sheet. <br />Chemical resistance (extract): <br />Freshwater, seawater, fertilizer, household effluent, <br />industrial effluent, organic acids such as e.g. acetic acid.</p> <p>This technical data sheet is a translation from German and does not consider local building codes or legal requirements. It shall be used as general reference for the product. Legally binding <br />is only the latest German technical data sheet or the latest data sheet from one of our foreign subsidiaries inside their sales territory.</p> <p>2/2</p> <p>Höl/CoS/TM</p> <p>10/17</p>
